Aerial Observation - MPCD - BIOSINFO

We propose to clean the areas, the sand and the vegetation "In Site" with Biodegradable Chemicals MPCD and Biological Acceptable Products BIOSINFO that are Environmentally Friendly to accelerate the process of Biodegradation. To do that we need heavy machinery to mix the products with the soil and sand and a lot of hand labor "In Site".

Aerial Observation

Aerial reconnaissance is an essential element of effective response to marine oil spills. It is used for assessing the location and extent of oil contamination and verifying predictions of the movement and fate of oil slicks at sea. Aerial surveillance provides information facilitating deployment and control of operations at sea, the timely protection of sites along threatened coastlines and the preparation of resources for shoreline clean-up. Observation can be undertaken visually or by use of remote sensing systems.

Visual Observation

Visual observation of floating oil from the air is the simplest method of determining the location and scale of an oil spill. However, obtaining worthwhile results requires detailed preparation before takeoff and careful interpretation of the information gathered. Surveillance of spilled oil can be undertaken by helicopter, particularly over near-shore waters where their flexibility is an advantage along intricate coastline with cliffs, coves and islands. Over the open sea, there is less need for rapid changes in flying speed, direction and altitude, and the speed and range of fixed-wing aircraft are more advantageous. However, any aircraft used must feature good all-round visibility and carry suitable navigational aids.

The position of the oil may be predicted using wind and current data. Floating oil will move downwind at about 3% of the wind speed and at 100% of the strength of surface water currents. Close to land, the strength and direction of any tidal currents must be considered when predicting oil movement, whereas further out to sea the contribution of other ocean currents predominate over the cyclic nature of tidal movement. Computer models can plot oil spill trajectories but the accuracy of any method depends on the quality of hydrographic data used and the reliability of forecasts of wind speed and direction.

It is usually necessary to plan a systematic aerial search to ascertain the presence or absence of oil over a large sea area. A 'ladder search' is frequently the most economical method of surveying an area. When planning a search, due attention must be paid to visibility and altitude, the likely flight duration and fuel availability. Floating oil has a tendency to become elongated and aligned parallel to the direction of the wind in long and narrow 'windrows' typically 30 - 50 metres apart. It is advisable to arrange a ladder search across the direction of the prevailing wind to increase the chances of oil detection.

Methods for observation and recording

Accurate observation will be assisted by having available extracts or copies of maps and charts and basic data such as the location of the spill source and of pertinent coastal features. Careful annotation of this plan during the flight of the time and locations of all potentially relevant features will create a reliable record from which an informative report of the flight can be prepared. In particular, for response efforts to be focused on the most significant areas of the spill, it is important to note the relative and heaviest concentrations of oil. GPS and other aircraft positioning systems allow pinpointing the oil's location. Photography, particularly digital photography, is also a useful recording tool and allows others to view the situation on return to base. Dedicated remote sensing aircraft often have built-in downward looking cameras linked with a GPS to assign accurate geographic co-ordinates.

Common errors

From the air it is notoriously difficult to distinguish between oil and a variety of other unrelated phenomena and it is necessary to verify initial sightings of suspected oil by over-flying suspect area at a sufficiently low altitude to allow positive identification. Phenomena that most often lead to mistaken reports of oil include: cloud shadows, ripples on the sea surface, differences in the colour of two adjacent water masses, suspended sediments, floating seaweed, algal/plankton blooms, seagrass and coral patches in shallow water (as shown in the image above), and sewage and industrial discharges.

Quantifying floating oil

An estimate of the quantity of oil observed at sea is important as guidance in planning the required scale of clean-up response. It is crucial therefore, that during the overflight the observer is able to distinguish between sheen and thicker patches of oil. However gauging the oil thickness and coverage is rarely easy and is made more difficult if the sea is rough. All such estimates should be viewed with considerable caution. The table below gives some guidance. Most difficult to assess are water-in-oil emulsions and viscous oils like heavy crude and fuel oil, which can vary in thickness from millimetres to several centimetres.

Oil Type   Appearance   Approximate
Thickness
  Approximate
Volume (m3/km2)
Oil Sheen   Silver   >0.0001mm   0.1
Oil Sheen   Iridescent   >0.0003mm   0.3
Crude and Fuel Oil   Brown to Black   >0.1mm   100
Water-in-oil Emulsions   Brown/Orange   >1mm   1000

Remote sensing

Remote sensing equipment mounted in aircraft is increasingly being used to monitor, detect and identify sources of illegal marine discharges and to monitor accidental oil spills. Remote sensors work by detecting properties of the sea surface: colour, reflectance, temperature or roughness. Oil can be detected on the water surface when it modifies one or more of these properties. Cameras relying on visible light are widely used, and may be supplemented by airborne sensors which detect oil outside the visible spectrum and are thus able to provide additional information about the oil. The most commonly employed combinations of sensors include Side-Looking Airborne Radar (SLAR) and downward-looking thermal infra-red (IR) and ultra-violet (UV) detectors or imaging systems. All sensors must be calibrated and require highly trained personnel to operate them and interpret the results.

Satellite imagery

Satellite-based remote sensing systems can also detect oil on water. The sensors on board are either optical, detecting in the visible and near infra red regions of the spectrum, or use radar. Optical observation of spilt oil by satellite requires clear skies, thereby severely limiting the usefulness of such systems. SAR (Synthetic Aperture Radar) is not restricted by the presence of cloud and is a more useful tool. However, with radar imagery, it is often difficult to be certain that an anomalous feature on a satellite image is caused by the presence of oil. Consequently, radar imagery from SAR requires expert interpretation by suitably trained personnel to avoid other features being mistaken for oil spills. To date, operational use has not been possible because of the time intervals between satellite overpasses and the time necessary to process the data. However, such imagery can be used later to complement aerial observations and provide a wider picture of the extent of pollution.

MPCD - BIOSINFO - THERMAL DESORPTION PROCESS

Disclaimer: Different factors apply to all the situations in which AAA Construction & Development provides technical advice, information and assistance and specific guidance should always be sought when dealing with specific situations. AAA Construction & Development does not warrant that the advice and information on this website will be complete or accurate or appropriate in all situations, and AAA Construction & Development excludes, to the fullest extent permitted by law, any liability to any person, corporation or other entity for any loss, damage, costs or expenses resulting from any reliance on or use of this website.